Just How to Install a Bathtub Yourself: Removing as well as Replacing.
Just How to Install a Bathtub Yourself: Removing as well as Replacing.
Blog Article
Are you in search of content around How to Install a Bathtub?
Mounting a bathtub isn't specifically rocket science, however it does call for solid plumbing, woodworking, and often, tiling skills. Replacing an old bath tub with a new one is additionally a reasonably hard project. If the old bathtub is conveniently available, the task can move immediately; if you need to open a wall to get rid of the old tub and position the brand-new bath tub, the task is much harder. In either instance, the job is within a home handyman's abilities, although you will require an assistant to leave the old bathtub and embeded in the new one. Ensure you have actually qualified yourself for the work and are comfortable trying it. As opposed to employing a service provider to take over a halfway-completed job, it is far better to consider utilizing one prior to you begin. Possibilities are you might need an expert plumber to make tube links.
This article will assist you mount a new tub in your washroom if you have already purchased a brand-new bathtub and don't need to alter the setup of your previous water supply pipes.
Your tools as well as product checklist ought to comprise the following:
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your installment, after that the first thing you need to do is disconnect the water system. After doing so, activate the faucets to drain any water remaining in the system. The procedure of removing the existing taps can be quite problematic because of the restricted gain access to that is frequently the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the faucets. Have a towel ready for the remaining water that will come from the pipelines. As soon as the supply pipelines have actually been gotten rid of, make use of the same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single taps from turning during this process. Once the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any type of old sealing compound.
Before moving on to fit the new taps, contrast the pipeline connections on the old taps to the new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new faucets to fit.
Suitable New Touches
If the tails of the new taps are plastic, then you will certainly require a plastic port to avoid damage to the string. One end of the adapter fits on the plastic tail of the faucet as well as the other end provides a connection to the current supply pipelines.
If you need to fit a monobloc, then you will certainly require reducing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, place the faucet in the mounting opening in the bath/basin making sure that the washers are in area in between the tap and also the sink. Protect the tap in place with the maker supplied backnut. Once the faucet is safely in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular faucet connectors. The previous kind ought to be attached to the faucet ends initially, tightening only by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have been linked.
Installing the Tub
Using both wooden boards under its feet, put the bathtub in the needed placement. The wooden boards are handy in evenly spreading out the weight of the bathtub over the location of the boards instead of concentrating all the weight onto 4 little factors.
The next objective is to ensure that the tub is leveled all round. This can be attained by inspecting the level and also readjusting the feet on the bathtub until the spirit level reviews level.
To set up faucets, fit the bottom of the outermost flexible tap adapter to the appropriate supply pipeline by making a compression join; after that do the very same for the other faucet.
Activate the supply of water as well as inspect all joints and also new pipework for leaks as well as tighten them if necessary. Fill the tub as well as also inspect the overflow electrical outlet and also the normal outlet for leaks.
Lastly, deal with the bath paneling as explained in the maker's user's manual. Tiling and also sealing around the tub should wait until the tub has actually been used a minimum of when as this will certainly settle it right into its last position.
Getting ready for the Installation
First of all, the sustaining structure supplied with the bath must be fitted (if called for) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is necessary to see to it that if the tap includes a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the taps unit to prevent stress on the tub.
Fit the adaptable faucet connectors to the bottom of the two taps utilizing 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet with the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Ensure you use all of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom ought to now be ready to be suited its last setting.
Tiling Around the Bathtub
In the area where the bathroom fulfills the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to crack an inflexible seal, creating the water to permeate the wall in between the bathroom as well as the tiling, leading to difficulties with moisture and feasible leaks to the ceiling below.
You can pick from a range of coloured sealants to assimilate your components and installations. They are offered in tubes and cartridges, and also are capable of sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with twists of drenched newspaper or soft rope. Bear in mind to constantly fill the tub with water before securing, to allow for the activity experienced when the bathtub is in usage. The sealant can fracture rather very early if you do not consider this activity before securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also quickly available on the marketplace. It is suggested to fit the floor tiles utilizing waterproof or waterproof sticky and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you really like reading up on Installing A Bathtub? Write a remark down below. We will be pleased to hear your ideas about this article. In hopes that you visit us again later on. Kindly take the opportunity to share this blog entry if you enjoyed it. We cherish reading our article about A Step-by-Step Guide to Installing a Bathtub.
Need Help? Hire Us Now! Report this page